Provides standards for the design of heliports serving helicopters with single rotors. Basic concepts can also be applied to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors; although many standards will not apply to these facilities.
This version adds guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO); turbulence effects; clearance between parking areas and taxi routes and within parking areas; minimum dimensions of curved approach/departure airspace; Touchdown/Positioning Circle (TDPC) Marking; Flight Path Alignment Guidance markings and lights; Emergency Helicopter Landing Facility Requirements (EHLF); FATO to FATO separation distance for simultaneous operations; revised standards for size of “H” for general aviation heliports; increased TLOF size when the FATO of a hospital heliport is not load bearing; and Heliport Protection Zone (HPZ) for hospital heliports. See "Principal Changes" for a complete list.
Airport Ground Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Out Squitter Equipment
Provides guidance on the development, installation, testing, approval, and maintenance of Automatic Dependent Surveillance – Broadcast (ADS-B) Out squitter units for airport ground vehicles. Using this AC, airports will be able to acquire approved and authorized airport ground vehicle ADS-B squitter units that are compliant with Title 14 Code of Federal Regulations (CFR), Part 91, Automatic Dependent Surveillance-Broadcast (ADS–B) Out Performance Requirements to Support Air Traffic Control (ATC) Service, as well as the initial set of ADS-B applications. Please note that the technical specifications for manufacturing ADS-B squitter units for airport ground vehicles are published in the FAA’s document, Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Specification, Version 2.4, published May 1, 2012.
Contact the appropriate FAA Airport District Office or Regional Airports Division to discuss Airport Improvement Program (AIP) eligibility.
Learn more about Automatic Dependent Surveillance-Broadcast (ADS-B).
Standards for Using Remote Sensing Technologies in Airport Surveys
Provides guidance on the use of remote sensing technologies in the collection of data describing the physical infrastructure of an airport. This version is a substantial rewrite and includes new sections on remote sensing technologies other than aerial imagery (primarily LIDAR) for collecting airport data. See also the Airports GIS website.
Use of Nondestructive Testing in the Evaluation of Airport Pavements
Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. It also briefly introduces other types of nondestructive measuring equipment to illustrate how supplementing NDT data with other test data may improve the quality and reliability of the pavement evaluation. This version updates Chapter 8, NDT-Based Evaluation and Design Updates, to reflect the requirements of the pavement design program FAARFIELD rather than the previous design program LEDFAA.
See also Airport Design Software.
Airside Applications for Artificial Turf
Provides guidance for the planning, design, installation, and maintenance of aviation grade artificial turf in areas adjacent to the operational areas of an airport.
Precision Approach Path Indicator (PAPI) Systems
Contains the FAA standards for the Precision Approach Path Indicator (PAPI) systems, which provides pilots with visual glideslope guidance during approach for landing.
Specification for L-890 Airport Lighting Control and Monitoring System (ALCMS)
Specifies the minimum requirements for an Airport Lighting Control and Monitoring System (ALCMS). The ALCMS simplifies the control and monitoring of lighted visual aids and enhances airport safety. The basic function of the system remains the same whether for a general aviation airport that supports only a few operations in a day or a large commercial airport which caters to hundreds of operations on any given day.
Operational Safety on Airports During Construction
Provides guidelines for operational safety on airports during construction. Principal changes include prohibiting construction in safety areas when associated runway or taxiway is open, providing guidance for incorporating safety risk management, and including checklists for writing Construction Safety and Phasing Plans (CSPP) and for daily inspections.
Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 184.108.40.206, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 220.127.116.11, Mounting System, to clarify Type II marker mounting and tethering requirements.
Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
Development of State Standards for Nonprimary Airports
Provides guidelines for the development of State standards for and the use of State highway specifications for pavement construction at nonprimary public-use airports as provided for in title 49 United States Code (USC), Sections 47105(c) and 47114(d)(5), respectively.
Specification for Series to Series Isolation Transformers for Airport Lighting Systems
Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.
Guide Specification for Aircraft Rescue and Fire Fighting (ARFF) Vehicles
Provides an interactive specification that airports can use in procuring Aircraft Rescue and Fire Fighting (ARFF) vehicles. It describes the selection process, vehicle requirements, and how to produce formal specifications.
Automated Weather Observing Systems(AWOS) for Non-Federal Applications
This advisory circular (AC) contains the Federal Aviation Administration’s (FAA) standard for the non-Federal AWOS. This AC applies to anyone proposing to design, procure, construct, install, activate or maintain an AWOS.
Airside Use of Heated Pavement Systems
Establishes minimum performance requirements for the design, construction, inspection, and maintenance of heated pavement systems for use in the Aircraft Operations Area (AOA).
Airport Avian Radar Systems
Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.
Aircraft Rescue and Fire Fighting (ARFF) Training Facilities
Provides guidance on the design, construction, and operation of aircraft rescue and fire fighting (ARFF) training facilities.
Airport Water Rescue Plans and Equipment
Provides guidance to assist airport operators in preparing for water rescue operations.
Specification for L-821, Panels for the Control of Airport Lighting
Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.
Specification for Runway and Taxiway Signs
Contains the FAA specifications for unlighted and lighted signs to be used on taxiways and runways. See also Engineering Brief 67: Light Sources Other than Incandescent and Xenon for Airport and Obstruction Lighting Fixtures.
Specification for Airport and Heliport Beacons
Contains equipment specifications for light beacons that are used to locate and identify civil airports, military airports, seaplane bases, and heliports.
Specification for Discharge-Type Flashing Light Equipment
Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).
See also Notice to Manufacturers of Airport Lighting and Navigation Aid Equipment about AIP Buy American Requirement (12/19/2011). The FAA is requesting information to determine if waivers to this requirement are needed.
Standards for Airport Sign Systems
Contains standards for the siting and installation of signs on airport runways and taxiways, including taxiway ending markers, location signs, runway distance remaining signs, mandatory hold signs associated with POFZ and CAT II/III operations, and many others.
Painting, Marking, and Lighting of Vehicles Used on an Airport
Provides guidance, specifications, and standards for painting, marking, and lighting of ground vehicles operating in the airport air operations area (AOA). The approved lights, colors, and markings described in the AC assure the conspicuity of vehicles operating in the AOA from both the ground and the air. The AC contains new specifications and recommendations for the painting, marking, and lighting of Towbarless Tow Vehicles (TLTVs).
Foreign Object Debris Detection Equipment
Provides information that airports can use to procure foreign object debris (FOD) detection equipment. Contains minimum performance specifications for systems and equipment that detect foreign objects on airports, including stationary radar, stationary electro-optical, stationary hybrid radar and electro-optical, and mobile radar.
See also Buy American Preferences to view:
Airport Pavement Design and Evaluation
Provides guidance to the public on the design and evaluation of pavements at civil airports.
See also related Airport Design Software.