|150/5320-15A||AAS-100||Management Of Airport Industrial Waste Provides basic information on the characteristics, management, and regulations of industrial wastes generated at airports. Provides guidance for the development of a Storm Water Pollution Prevention Plan (SWPPP) that applies best management practices to eliminate, prevent, or reduce pollutants in storm water runoff associated with particular airport industrial activities.||09-08-2008|
Measurement, Construction, and Maintenance of Skid Resistant Airport Pavement Surfaces
Contains guidelines and procedures for the design and construction of skid-resistant pavement; pavement evaluation, without or with friction equipment; and maintenance of high skid-resistant pavements.
|150/5370-13A||AAS-100||Off-Peak Construction of Airport Pavements Using Hot-Mix Asphalt Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of off-peak construction of airport pavements using hot-mix asphalt (HMA) paving materials. Also focuses on HMA airfield pavement construction and applies to other types of airfield improvements where off-peak construction is identified as the preferred delivery method.||09-29-2006|
Operational Safety on Airports During Construction
Provides guidelines for operational safety on airports during construction. Principal changes include prohibiting construction in safety areas when associated runway or taxiway is open, providing guidance for incorporating safety risk management, and including checklists for writing Construction Safety and Phasing Plans (CSPP) and for daily inspections.
Painting, Marking, and Lighting of Vehicles Used on an Airport
Provides guidance, specifications, and standards for painting, marking, and lighting of ground vehicles operating in the airport air operations area (AOA). The approved lights, colors, and markings described in the AC assure the conspicuity of vehicles operating in the AOA from both the ground and the air. The AC contains new specifications and recommendations for the painting, marking, and lighting of Towbarless Tow Vehicles (TLTVs).
Performance Specification for Airport Vehicle Runway Incursion Warning Systems (RIWS)
This AC contains minimum performance specifications for systems and equipment airports use to provide a warning to drivers on an airfield about a potential runway incursion. This AC discusses two types of detection systems: a preconfigured, commercial off the shelf (COTS) system; and a system with custom hardware and software.
Precision Approach Path Indicator (PAPI) Systems
Contains the FAA standards for the Precision Approach Path Indicator (PAPI) systems, which provides pilots with visual glideslope guidance during approach for landing.
Predesign, Prebid, and Preconstruction Conferences for Airport Grant Projects
Provides guidance for conducting predesign, prebid, and preconstruction conferences for projects funded under the FAA airport grant program. This version adds quality acceptance as a topic of discussion for the preconstruction conference, items to be addressed in the engineer’s report, details about what should be included in the phasing plan, and discussion of construction management plans.
|150/5370-12A||AAS-100||Quality Control of Construction for Airport Grant Projects Provides information to ensure the quality of construction accomplished under the Airport Improvement Program (AIP).||09-29-2007|
|150/5370-16||AAS-100||Rapid Construction of Rigid (Portland Cement Concrete) Airfield Pavements Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of rapid construction of rigid (Portland Cement Concrete) airfield pavements. This AC focuses on rigid airfield pavement construction. The material contained herein also applies to other types of airfield improvements where rapid construction is identified as the preferred construction method.||09-28-2007|
|150/5325-4B||AAS-100||Runway Length Requirements for Airport Design Provides design standards and guidelines for determining recommended runway lengths.||07-01-2005|
This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.
Segmented Circle Airport Marker System
This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.
|150/5345-49C||AAS-100||Specification L-854, Radio Control Equipment Contains the specifications for radio control equipment to be used for controlling airport lighting facilities.||06-27-2007|
Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories
This AC contains the specifications for airport light bases, transformer housings, junction boxes, and accessories. This AC is not intended to be a compilation of currently available product designs. It provides the basic standard requirements for critical dimensions and performance requirements to which all manufacturers must demonstrate compliance.
Specification for Airport and Heliport Beacons
Contains equipment specifications for light beacons that are used to locate and identify civil airports, military airports, seaplane bases, and heliports.
Specification for Constant Current Regulators and Regulator Monitors
Contains a specification for constant current regulators (CCR) and a monitor for use with airport lighting circuits.
Specification for Discharge-Type Flashing Light Equipment
Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).
See also Notice to Manufacturers of Airport Lighting and Navigation Aid Equipment about AIP Buy American Requirement (12/19/2011). The FAA is requesting information to determine if waivers to this requirement are needed.
Specification for L-821, Panels for the Control of Airport Lighting
Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.
Specification for L-824 Underground Electrical Cable for Airport Lighting Circuits
This AC provides specifications for L-824 underground electrical cable for airport lighting circuits.
|150/5345-13B||AAS-100||Specification for L-841 Auxiliary Relay Cabinet Assembly for Pilot Control of Airport Lighting Circuits Contains the specification requirements for a relay cabinet used to control airfield lighting circuits. The L-841 consists of an enclosure containing a direct current (DC) power supply, control circuit protection and 20 pilot relays.||09-20-2007|
Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 18.104.22.168, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 22.214.171.124, Mounting System, to clarify Type II marker mounting and tethering requirements.
Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
Specification for L-884, Power and Control Unit for Land and Hold Short Lighting Systems
Contains the FAA standards for power and control units for land and hold short lighting systems.
Specification for L-890 Airport Lighting Control and Monitoring System (ALCMS)
Specifies the minimum requirements for an Airport Lighting Control and Monitoring System (ALCMS). The ALCMS simplifies the control and monitoring of lighted visual aids and enhances airport safety. The basic function of the system remains the same whether for a general aviation airport that supports only a few operations in a day or a large commercial airport which caters to hundreds of operations on any given day.
|150/5345-55A||AAS-100||Specification for L-893, Lighted Visual Aid to Indicate Temporary Runway Closure Provides guidance in the design of a lighted visual aid to indicate temporary runway closure.||06-27-2007|