|25.775-1||ANM-110||Windows and Windshields Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of Title 14, Code of Federal Regulations (14 CFR) part 25 pertaining to the certification requirements for windshields, windows, and mounting structure. Guidance information is provided for showing compliance with § 25.775(d), relating to structural design of windshields and windows for airplanes with pressurized cabins. Terms used in this AC, such as “shall” or “must,” are used only in the sense of ensuring applicability of this particular method of compliance when the acceptable method of compliance described herein is used. Other methods of compliance with the requirements may be acceptable. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with 14 CFR. This AC does not change, create any additional, authorize changes in, or permit deviations from, regulatory requirements.||01-17-2003|
|25.1455-1||ANM-112||Waste Water/Potable Water Drain System Certification Testing Sets forth a specific method of compliance with the requirements of section 25.1455 of the FAR pertaining to draining of fluids through drain masts when the fluids are subject to freezing. This method is designed to verify that draining fluids will not accumulate as ice in sufficient quantity to be hazardous. Is for guidance purposes and to set forth one method of compliance that has been found acceptable.||03-11-1985|
|25.807-1||ANM-114||Uniform Distribution of Exits Provides guidance material for acceptable means, but not the only means, of demonstrating compliance with the requirements for distributing required passenger emergency exits uniformly. Addresses only those passenger-carrying airplanes, including mixed passenger/cargo (“combi”) configurations, with a type certification basis for Amendment 25-15 or later with respect to Section 25.807(c) or airplanes with an earlier type certification basis required by Section 25.2 to meet Section 25.807, Amendment 25-15. Does not address airplanes with only one pair of required exits.||08-13-1990|
|25-18||ANM-114||Transport Category Airplanes Modified for Cargo Service Provides guidance for demonstrating compliance with the FAR pertaining to transport category airplanes converted for use in all-cargo or combination passenger/cargo (combi) service and the relationship of those regulations to the requirements of Parts 121and 135 of the FAR.||01-06-1994|
Transport Airplane Cabin Interiors Crashworthiness Handbook
This Advisory Circular (AC) provides acceptable certification methods, but not necessarily the only acceptable methods, for demonstrating compliance with the crashworthiness requirements of part 25, as amended through Amendment 25-112, of Title 14 of the Code of Federal Regulations (14 CFR) for transport category airplanes. The guidance in this AC is not mandatory nor a regulation.
|25.856-1||ANM-115||Thermal/Acoustic Insulation Flame Propagation Test Method Details Guidance applies to airplanes required to conform with 25.856, and part VI of appendix F to Title 14 Code of Federal Regulations (14 CFR) part 25.||06-24-2005|
|25.491-1||ANM-110||Taxi, Takeoff and Landing Roll Design Loads Sets forth acceptable methods of compliance with provisions of Part 25 of the FAR dealing with the certification requirements for taxi, takeoff, and landing roll design loads. Guidance information is provided for showing compliance with section 25.491 of the FAR relating to structural design for airplane operation on paved runways and taxiways normally used in commercial operations.||10-20-2000|
Takeoff Performance Data for Operations on Contaminated Runways
This advisory circular (AC) provides guidance and standardized methods that data providers, such as type certificate (TC) holders, supplemental type certificate (STC) holders, applicants, and airplane operators, can use when developing takeoff performance data for transport category airplanes for operations on contaminated runways. This AC also promotes the use of consistent terminology for runway surface conditions used among data providers and FAA personnel.
|25.703-1||ANM-111||Takeoff Configuration Warning Systems Provides guidance for the certification of takeoff configuration warning systems installed in transport category airplanes.||03-17-1993|
|25.1309-1A||ANM-112||System Design and Analysis Describes various acceptable means for showing compliance with the requirements of section 25.1309(b), (c), and (d) of the Federal Aviation Regulations (FAR). These means are intended to provide guidance for the experience engineering and operational judgment that must form the basis for compliance findings.||06-21-1988|
|25-24||ANM-100||Sustained Engine Imbalance Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of 14 CFR Part 25 related to the aircraft design for sustained engine rotor imbalance conditions. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with the pertinent Federal Aviation Regulations (FAR).||08-02-2000|
|25.795-7||ANM-100||Survivability of Systems||10-24-2008|
|25-9A||ANM-111||Smoke Detection, Penetration, and Evacuation Tests and Related Flight Manual Emergency Procedures Provides guidelines for the conduct of certification tests relating to smoke detection, penetration, and evacuation and to evaluate related Airplane Flight Manual (AFM) procedures. These guidelines may be used to reduce the number of decisions based solely on judgment in conducting tests and evaluating test results. While not mandatory this AC offers a method of demonstrating compliance with the applicable airworthiness requirements.||01-06-1994|
|25.723-1||ANM-110||Shock Absorption Tests This advisory circular (AC) sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of part 25 of the Federal Aviation Regulations (FAR) related to the use of landing gear shock absorption tests and analyses to determine landing loads for transport category airplanes.||05-25-2001|
|25-13||ANM-112||Reduced and Derated Takeoff Thrust (Power) Procedures This advisory circular (AC) provides guidance for the certification and use of reduced thrust (power) for takeoff and derated takeoff thrust (power) on turbine powered transport category airplanes. It consolidates FAA guidance concerning this subject and serves as a ready reference for those involved with airplane certification and operation. These procedures should be considered during airplane type certification and supplemental type certification activities when less than engine rated takeoff thrust (power) is used for takeoff.||05-04-1988|
|25.1360-1||ANM-100||Protection Against Injury This advisory circular (AC) provides guidance for demonstrating compliance with the transport category airplane certification requirements of § 25.1360 Precautions against injury||10-22-2007|
|25-20||ANM-111||Pressurization, Ventilation and Oxygen Systems Assessment for Subsonic Flight including High Altitude Operation Provides guidance on methods of compliance with the requirements of part 25 of the Federal Aviation Regulations pertaining to pressurization, ventilation, and oxygen systems, especially as they pertain to high altitude subsonic flight. As with all AC material, it is not mandatory and does not constitute a regulation. The applicant may elect to follow alternate methods provided that these methods are also found by the FAA to be an acceptable means of complying with the requirements of part 25. Because the guidance on the methods of compliance presented in this AC are not mandatory, the terms "shall" and "must" when used herein, apply only to an applicant that chooses to follow a particular method without deviation.||09-10-1996|
|25.773-1||ANM-111||Pilot Compartment View Design Considerations Provides guidance for demonstrating compliance with the airworthiness standards for transport category airplanes pertaining to pilot compartment view. These criteria include the properties of transport materials necessary to assure adequate visibility from the flight deck.||01-08-1993|
Performance and Handling Characteristics in Icing Conditions
This advisory circular describes an acceptable means of showing compliance with the airplane performance and handling characteristics certification requirements for flight in the icing conditions defined in Appendices C and 0 of Title 14, Code of Federal Regulations part 25.
|25.795-4||ANM-100||Passenger Cabin Smoke Protection This Advisory Circular (AC) provides an acceptable means of showing compliance with the requirements of Title 14, Code of Federal Regulations (CFR), part 25, § 25.795(b)(2), “Cabin smoke protection.” This section requires that an airplane be designed with means to prevent passengers from being incapacitated by smoke, fumes, and noxious gases that result from detonation of an explosive or incendiary device during flight. The means of compliance described in this document provides guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to penetration of smoke, fumes, and noxious gases into the passenger cabin.||10-24-2008|
|25.1523-1||ANM-111||Minimum Flightcrew Sets forth a method of compliance with the requirements of Section 25.1523 of the FAR, which contains the certification requirements for minimum flight crew on transport category airplanes.||02-02-1993|
|25.905-1||ANM-110||Minimizing the Hazards from Propeller Blade and Hub Failures Describes an acceptable means for showing compliance with the requirements of Section 25.905, “Propellers,” of Title 14, Code of Federal Regulations (CFR) Part 25. It provides guidance on design precautions to take to minimize the hazards that could occur to an airplane if a propeller blade fails or is released by a hub failure. The AC addresses the hazards associated with impact damage.||09-27-2000|
|25.613-1||ANM-115||Material Strength Properties and Material Design Values||08-06-2003|
|25.795-6||ANM-100||Least Risk Bomb Location This advisory circular (AC) describes an acceptable means for showing compliance with the requirements of Title 14, Code of Federal Regulations (CFR), part 25, § 25.795(c), “Least risk bomb location.” This section requires that a location on the airplane be designed where an explosive or incendiary device may be placed to protect flight critical structures and systems from damage in case of detonation. The means of compliance described in this document provide guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to the design of a Least Risk Bomb Location on an airplane.||10-24-2008|
Landing Performance Data for Time-of-Arrival Landing Performance Assessments
This AC provides guidance and standardized methods that data providers, such as TC holders, STC holders, applicants, and airplane operators, can use when developing landing performance data for time-of-arrival landing performance assessments for transport category airplanes. This AC also promotes the use of consistent terminology for runway surface conditions used among data providers and FAA personnel.