Back to Advisory Circulars Main Page

Will search within "Airworthiness Standards: Transport Category Airplanes" only. Search all ACs.

51 - 75 of 76 results.
First Previous 1 2 [3] 4 Next Last
Number Office Title Date
25.1302-1 ANM-111 Installed Systems and Equipment for Use by the Flightcrew

This advisory circular (AC) provides guidance for the design and methods of compliance for installed equipment on transport airplanes intended for use by the flightcrew. The guidance provided by this AC is intended to minimize the occurrence of design-related errors by the flightcrew and to enable the flightcrew to detect and manage errors that do occur. This AC provides recommendations for the design and evaluation of controls, displays, system behavior, and system integration that are all part of human factors considerations.

AH Bahrami

05-03-2013
25.1529-1A ANM-100 Instructions for Continued airworthiness of Structural Repairs on Transport Airplanes Provides instructions to ensure continued airworthiness of structural repairs on transport category airplanes. It addresses the approval procedures to follow when making structural repairs to structure certificated under the damage tolerance requirements of Section 25.571 of FAR, Amendment 25-45, and to type designs with Supplemental Inspection Documents, which were based on these criteria. 11-20-2007
25.795-8 ANM-100 Interior Design to Facillitate Searches This advisory circular (AC) describes an acceptable means for showing compliance with the requirements of Title 14, Code of Federal Regulations (14 CFR), part 25, § 25.795(c)(3), “Interior design to facilitate searches.” This section requires that the interior design of an airplane incorporate features that will make it more difficult to hide dangerous objects in the airplane or make it easier to find them if they have been brought onboard. The means of compliance described in this document provides guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to whether the interior design deters concealment of dangerous objects (e.g., weapons or explosives) and facilitates a search for them in certain areas of the airplane. The requirements for searching an airplane are not affected by the requirements of § 25.795(c)(3). The design of the airplane will make it easier to search for hidden objects but will not affect the need for, or the diligence of, the search. 10-24-2008
25.795-6 ANM-100 Least Risk Bomb Location This advisory circular (AC) describes an acceptable means for showing compliance with the requirements of Title 14, Code of Federal Regulations (CFR), part 25, § 25.795(c), “Least risk bomb location.” This section requires that a location on the airplane be designed where an explosive or incendiary device may be placed to protect flight critical structures and systems from damage in case of detonation. The means of compliance described in this document provide guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to the design of a Least Risk Bomb Location on an airplane. 10-24-2008
25.613-1 ANM-115 Material Strength Properties and Material Design Values 08-06-2003
25.905-1 ANM-110 Minimizing the Hazards from Propeller Blade and Hub Failures Describes an acceptable means for showing compliance with the requirements of Section 25.905, “Propellers,” of Title 14, Code of Federal Regulations (CFR) Part 25. It provides guidance on design precautions to take to minimize the hazards that could occur to an airplane if a propeller blade fails or is released by a hub failure. The AC addresses the hazards associated with impact damage. 09-27-2000
25.1523-1 ANM-111 Minimum Flightcrew Sets forth a method of compliance with the requirements of Section 25.1523 of the FAR, which contains the certification requirements for minimum flight crew on transport category airplanes. 02-02-1993
25.795-4 ANM-100 Passenger Cabin Smoke Protection This Advisory Circular (AC) provides an acceptable means of showing compliance with the requirements of Title 14, Code of Federal Regulations (CFR), part 25, § 25.795(b)(2), “Cabin smoke protection.” This section requires that an airplane be designed with means to prevent passengers from being incapacitated by smoke, fumes, and noxious gases that result from detonation of an explosive or incendiary device during flight. The means of compliance described in this document provides guidance to supplement the engineering and operational judgment that must form the basis of any compliance findings relative to penetration of smoke, fumes, and noxious gases into the passenger cabin. 10-24-2008
25-25 ANM-110 Performance and Handling Characteristics in the Icing Conditions Specified in Part 25, Appendix C This advisory circular (AC) describes an acceptable means for showing compliance with the airplane certification requirements related to performance and handling characteristics of transport category airplanes for flight in the icing conditions defined in appendix C of Title 14, Code of Federal Regulations (14 CFR) part 25. Part 25 contains the airworthiness standards applicable to transport category airplanes. The means of compliance described in this document provide guidance to find compliance relative to airplane performance and handling characteristics in appendix C icing conditions. 09-10-2007
25.773-1 ANM-111 Pilot Compartment View Design Considerations Provides guidance for demonstrating compliance with the airworthiness standards for transport category airplanes pertaining to pilot compartment view. These criteria include the properties of transport materials necessary to assure adequate visibility from the flight deck. 01-08-1993
25-20 ANM-111 Pressurization, Ventilation and Oxygen Systems Assessment for Subsonic Flight including High Altitude Operation Provides guidance on methods of compliance with the requirements of part 25 of the Federal Aviation Regulations pertaining to pressurization, ventilation, and oxygen systems, especially as they pertain to high altitude subsonic flight. As with all AC material, it is not mandatory and does not constitute a regulation. The applicant may elect to follow alternate methods provided that these methods are also found by the FAA to be an acceptable means of complying with the requirements of part 25. Because the guidance on the methods of compliance presented in this AC are not mandatory, the terms "shall" and "must" when used herein, apply only to an applicant that chooses to follow a particular method without deviation. 09-10-1996
25.1360-1 ANM-100 Protection Against Injury This advisory circular (AC) provides guidance for demonstrating compliance with the transport category airplane certification requirements of § 25.1360 Precautions against injury 10-22-2007
25-13 ANM-112 Reduced and Derated Takeoff Thrust (Power) Procedures This advisory circular (AC) provides guidance for the certification and use of reduced thrust (power) for takeoff and derated takeoff thrust (power) on turbine powered transport category airplanes. It consolidates FAA guidance concerning this subject and serves as a ready reference for those involved with airplane certification and operation. These procedures should be considered during airplane type certification and supplemental type certification activities when less than engine rated takeoff thrust (power) is used for takeoff. 05-04-1988
25.723-1 ANM-110 Shock Absorption Tests This advisory circular (AC) sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of part 25 of the Federal Aviation Regulations (FAR) related to the use of landing gear shock absorption tests and analyses to determine landing loads for transport category airplanes. 05-25-2001
25-9A ANM-111 Smoke Detection, Penetration, and Evacuation Tests and Related Flight Manual Emergency Procedures Provides guidelines for the conduct of certification tests relating to smoke detection, penetration, and evacuation and to evaluate related Airplane Flight Manual (AFM) procedures. These guidelines may be used to reduce the number of decisions based solely on judgment in conducting tests and evaluating test results. While not mandatory this AC offers a method of demonstrating compliance with the applicable airworthiness requirements. 01-06-1994
25.795-7 ANM-100 Survivability of Systems 10-24-2008
25-24 ANM-100 Sustained Engine Imbalance Sets forth an acceptable means, but not the only means, of demonstrating compliance with the provisions of 14 CFR Part 25 related to the aircraft design for sustained engine rotor imbalance conditions. While these guidelines are not mandatory, they are derived from extensive Federal Aviation Administration (FAA) and industry experience in determining compliance with the pertinent Federal Aviation Regulations (FAR). 08-02-2000
25.1309-1A ANM-112 System Design and Analysis Describes various acceptable means for showing compliance with the requirements of section 25.1309(b), (c), and (d) of the Federal Aviation Regulations (FAR). These means are intended to provide guidance for the experience engineering and operational judgment that must form the basis for compliance findings. 06-21-1988
25.703-1 ANM-111 Takeoff Configuration Warning Systems Provides guidance for the certification of takeoff configuration warning systems installed in transport category airplanes. 03-17-1993
25.491-1 ANM-110 Taxi, Takeoff and Landing Roll Design Loads Sets forth acceptable methods of compliance with provisions of Part 25 of the FAR dealing with the certification requirements for taxi, takeoff, and landing roll design loads. Guidance information is provided for showing compliance with section 25.491 of the FAR relating to structural design for airplane operation on paved runways and taxiways normally used in commercial operations. 10-20-2000
25.856-1 ANM-115 Thermal/Acoustic Insulation Flame Propagation Test Method Details Guidance applies to airplanes required to conform with 25.856, and part VI of appendix F to Title 14 Code of Federal Regulations (14 CFR) part 25. 06-24-2005
25-17A ANM-100 Transport Airplane Cabin Interiors Crashworthiness Handbook

This Advisory Circular (AC) provides acceptable certification methods, but not necessarily the only acceptable methods, for demonstrating compliance with the crashworthiness requirements of part 25, as amended through Amendment 25-112, of Title 14 of the Code of Federal Regulations (14 CFR) for transport category airplanes. The guidance in this AC is not mandatory nor a regulation.

05-18-2009
25-18 ANM-114 Transport Category Airplanes Modified for Cargo Service Provides guidance for demonstrating compliance with the FAR pertaining to transport category airplanes converted for use in all-cargo or combination passenger/cargo (combi) service and the relationship of those regulations to the requirements of Parts 121and 135 of the FAR. 01-06-1994
25.807-1 ANM-114 Uniform Distribution of Exits Provides guidance material for acceptable means, but not the only means, of demonstrating compliance with the requirements for distributing required passenger emergency exits uniformly. Addresses only those passenger-carrying airplanes, including mixed passenger/cargo (“combi”) configurations, with a type certification basis for Amendment 25-15 or later with respect to Section 25.807(c) or airplanes with an earlier type certification basis required by Section 25.2 to meet Section 25.807, Amendment 25-15. Does not address airplanes with only one pair of required exits. 08-13-1990
25.1455-1 ANM-112 Waste Water/Potable Water Drain System Certification Testing Sets forth a specific method of compliance with the requirements of section 25.1455 of the FAR pertaining to draining of fluids through drain masts when the fluids are subject to freezing. This method is designed to verify that draining fluids will not accumulate as ice in sufficient quantity to be hazardous. Is for guidance purposes and to set forth one method of compliance that has been found acceptable. 03-11-1985
51 - 75 of 76 results.
First Previous 1 2 [3] 4 Next Last