Aeroelastic Stability Substantiation of Transport Category Airplanes
This advisory circular (AC) provides guidance material for acceptable means, but not the only means, of demonstrating compliance with the provisions of Title 14, Code of Federal Regulations part 25 associated with the design requirements for transport category airplanes to preclude the aeroelastic instabilities offlutter, divergence, and control reversal. The precise details for analytical procedures and testing techniques are beyond the scope of this AC. However, some general information is included, with supporting discussions, for consideration when demonstrating compliance with§ 25.629 and related regulations. Revision B incorporates changes only to the portions of this AC affected by the Airplane and Engine Certification Requirements in Supercooled Large Drop, Mixed Phase, and Ice Crystal Icing Conditions final ru
|25.783-1A||ANM-115||Fuselage Doors and Hatches Sets forth acceptable means of compliance with the provisions of Part 25 of the Federal Aviation Regulations (FAR) dealing with the certification requirements of fuselage doors. Guidance information is provided for showing compliance with structural and functional safety standards for doors and their operating systems. The intent of the requirements and some acceptable means of compliance are discussed. Other means are acceptable if they meet the intent of the regulations. For the propose of showing compliance with section 25.783 of FAR, hatches and exits are also considered to be doors.||04-25-2005|
Emergency Evacuation Demonstrations
This advisory circular (AC) provides guidance on means, but not the only means, of compliance with Title 14, Code of Federal Regulations (14 CFR) part 25 concerning: (1) conduct of full?scale emergency evacuation demonstrations, and (2) use of analysis and tests in lieu of conducting an actual demonstration. Throughout this AC, any reference to a full-scale demonstration, unless further qualified, means an evacuation demonstration in which a full complement of passengers and the requisite number of crewmembers evacuate an airplane using assist means, if installed, under the conditions specified in part 25, appendix J. References to “appendix J” means 14 CFR part 25, appendix J. Additionally, any reference to an analysis, which is to be used to satisfy the emergency evacuation requirements of part 25, means a formal analysis document supported by data from tests or demonstrations. Terms such as “shall” and “must” are used only in the sense of ensuring applicability of this particular means of compliance when the acceptable means of compliance described herein is used.
|25.856-1||ANM-115||Thermal/Acoustic Insulation Flame Propagation Test Method Details Guidance applies to airplanes required to conform with 25.856, and part VI of appendix F to Title 14 Code of Federal Regulations (14 CFR) part 25.||06-24-2005|
Installation of Thermal/Acoustic Insulation for Burnthrough Protection
This AC provides guidance for the test method to determine burnthrough resistance of thermal/acoustic insulation materials installed in transport category airplanes. This guidance applies to airplanes required to comply with § 25.856 and part VII of Appendix F to 14 CFR part 25.
Certification Maintenance Requirements
This advisory circular (AC) provides guidance on the selection, documentation, and control of Certification Maintenance Requirements (CMR). This AC also provides a rational basis for coordinating the Maintenance Review Board (MRB), if the MRB process is used, and CMR selection processes to ensure premises made in the system safety analyses supporting the compliance with the requirements of Title 14, Code of Federal Regulations (14 CFR) 25.1309, and other system safety rules (such as §§ 25.671, 25.783, 25.901, and 25.933) are protected in service. This AC describes an acceptable means, but not the only means, for selecting, documenting, and managing CMRs. Terms such as "shall" and "must" are used only in the sense of ensuring applicability of this particular means of compliance when the acceptable means of compliance described herein is used.
|25-23||ANM-130L||Airworthiness Criteria for the Installation Approval of a Terrain Awareness and Warning System (TAWS) for Part 25 Airplanes Describes an acceptable means for obtaining FAA airworthiness approval for the installation of a Terrain Awareness and Warning System (TAWS) that has been approved under Technical Standard Order (TSO)-C151a.||05-22-2000|