Qualifications for Wildlife Biologist Conducting Wildlife Hazard Assessments and Training Curriculums for Airport Personnel Involved in Controlling Wildlife Hazards on Airports (Consolidated AC includes Change 1)
Describes the qualifications for wildlife biologists who conduct Wildlife Hazard Assessments (WHA) for airports certificated under 14 CFR Part 139 and at non-certificated airports funded by the Airport Improvement Program (AIP) or Passenger Facility Charge (PFC) Program. Addresses the minimum wildlife hazard management curriculum for the initial and recurrent training of airport personnel who implement an FAA-approved Wildlife Hazard Management Plan (WHMP).
Consolidated AC includes Change 1 dated 1/31/2013. See also--
Provides standards for the design of heliports serving helicopters with single rotors. Basic concepts can also be applied to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors; although many standards will not apply to these facilities.
This version adds guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO); turbulence effects; clearance between parking areas and taxi routes and within parking areas; minimum dimensions of curved approach/departure airspace; Touchdown/Positioning Circle (TDPC) Marking; Flight Path Alignment Guidance markings and lights; Emergency Helicopter Landing Facility Requirements (EHLF); FATO to FATO separation distance for simultaneous operations; revised standards for size of “H” for general aviation heliports; increased TLOF size when the FATO of a hospital heliport is not load bearing; and Heliport Protection Zone (HPZ) for hospital heliports. See "Principal Changes" for a complete list.
Aircraft Boarding Equipment
Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers. The physical area covered in this AC is that which is bounded by the door of the passenger terminal area, on one end, to the door of the aircraft, on the other end. Although this AC refers only to aircraft boarding (enplaning), all references apply equally to disembarking (deplaning) with the described procedures occurring in reverse order.
The previous version of this AC discussed only the passenger lift scenario and associated equipment. This document updates that effort and addresses the other methods and equipment used to board an aircraft, including passenger boarding bridges, ramps, lifts, and aircraft boarding chairs.
Federal Surplus Personal Property Program for Public Airport Purposes
This AC explains to public airport sponsors and other interested parties the Federal Surplus Personal Property Program for Public Airports. It contains the procedures for applying for screener credentials and to request authorized surplus personal property through the GSAXcess system administered by the General Services Administration (GSA) for disposition of federal surplus personal property.
Design and Installation Details for Airport Visual Aids
Provides guidance and recommendations on the installation of airport visual aids.
Specification for Obstruction Lighting Equipment
This specification sets forth the FAA requirements for obstruction lighting equipment used to increase conspicuity of structures to permit early obstruction recognition by pilots.
Airport Lighting Equipment Certification Program
This AC describes the Airport Lighting Equipment Certification Program (ALECP). It provides information on how an organization can get Federal Aviation Administration (FAA) acceptance as a third-party certification body (third-party certifier) and how manufacturers may get equipment qualified under the program. It includes a list of the equipments that are certified under the program. This AC does not impose requirements or mandate participation in the ALECP by any party. This revision clarifies the criteria that FAA will use to determine whether a certification body qualifies for participation and how equipment may be qualified.
Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns
Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).
Performance Specification for Airport Vehicle Runway Incursion Warning Systems (RIWS)
This AC contains minimum performance specifications for systems and equipment airports use to provide a warning to drivers on an airfield about a potential runway incursion. This AC discusses two types of detection systems: a preconfigured, commercial off the shelf (COTS) system; and a system with custom hardware and software.
Aircraft Fuel Storage, Handling, Training, and Dispensing on Airports
Contains specifications and guidance for the storage, handling, and dispensing of aviation fuel on airports. Additionally, this AC provides standards and guidance for the training of personnel who conduct these activities.
Please see the associated Addendum for a list of companies offering courses of instruction in line service training as well as supervisory training that are acceptable to the Administrator. We will update the Addendum on a quarterly basis.
Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.
Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories
This AC contains the specifications for airport light bases, transformer housings, junction boxes, and accessories. This AC is not intended to be a compilation of currently available product designs. It provides the basic standard requirements for critical dimensions and performance requirements to which all manufacturers must demonstrate compliance.
Reporting Wildlife Aircraft Strikes
This AC explains the importance of reporting collisions between aircraft and wildlife, more commonly referred to as wildlife strikes. It also explains recent improvements in the FAA’s Bird/Other Wildlife Strike Reporting system, how to report a wildlife strike, what happens to the wildlife strike report data, how to access the FAA National Wildlife Strike Database (NWSD), and the FAA’s Feather Identification program.
Announcement of Availability of Airport-Related Research and Development Products
This AC explains how to obtain the latest airport-related research and development (R&D) products funded by the Federal Aviation Administration’s (FAA’s) Airports Organization, particularly the FAA’s Airport Technology Research and Development Branch, the Airport Cooperative Research Program (ACRP), the Innovative Pavement Research Foundation (IPRF), and the Airfield Asphalt Pavement Technology Program (AAPTP).
This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.
Design of Aircraft Deicing Facilities
This AC provides standards and recommendations for use in the design of aircraft deicing facilities.
Airport Drainage Design
This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons. It incorporates the DOD Unified Facilities Criteria (UFC) draft document, Surface Drainage Design, dated August 1, 2006. This revision adds guidance that was not included in the original DOD document. See paragraph 5,, "Purpose of this Revision."
Specification for L-824 Underground Electrical Cable for Airport Lighting Circuits
This AC provides specifications for L-824 underground electrical cable for airport lighting circuits.
Segmented Circle Airport Marker System
This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.
Specification for Wind Cone Assemblies
This AC contains a specification for wind cone assemblies to be used to provide wind information to pilots. This revision revises the equipment qualification requirements to be furnished under the Federal grant assistance program for airports, applies photometric requirements for internally lighted wind cones to both Size 1 and Size 2 windsocks, and makes editorial changes.
Airport Signing and Graphics
This AC provides guidance on airport terminal and landside wayfinding, signing, and graphics. It focuses on four areas of the airport: roadways, parking, curbside and ground transportation, and terminal. This version is a substantial rewrite and incorporates the recommendations and guidelines developed under Airport Cooperative Research Program (ACRP) Report 52, Wayfinding and Signing Guidelines for Airport Terminals and Landside, completed in 2011.
Standards for Airport Markings
This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons.