Provides guidance to the public on the design and evaluation of pavements at civil airports.

Because of the size of the document, it is available as one large file (see Complete) or as four smaller files (see Parts 1-4).

See also related Airport Design Software.

Provides guidance for engineers, airport managers, and the public in the design and maintenance of airport surface drainage systems. Combines existing surface drainage topics covered in different agency manuals into one Unified Facilities Criteria (UFC) document that will serve as the design and analysis standard for surface drainage for FAA and the Department of Defense. Consolidated file contains Change 1.

The AC is 12.7 MB (see Complete file). Because of its size, the AC has been broken into several parts to make it easier to download (see Parts 1-13).

Provides the specifications for the collection of airport data for the FAA Airport Surveying – Geographic Information System (GIS) Program. Also explains how to submit data to the FAA, which will forward the safety critical data to the National Geodetic Survey (NGS) for independent verification and validation. The standards covered in this document provide critical information for the operation and safety of the National Airspace System (NAS) and are classified as critical by the International Civil Aviation Organization (ICAO). ICAO Annex 15 defines data as critical when “there is a high probability when using corrupted critical data that the continued safe flight and landing of an aircraft would be severely at risk with the potential for catastrophe.” The information furnished under these standards covers the entire spectrum of the FAA’s airport data requirements. See also FAA Airport Surveying - GIS Program and Airports GIS Video Training Series.

Provides guidance on the use of remote sensing technologies in the collection of data describing the physical infrastructure of an airport. This version is a substantial rewrite and includes new sections on remote sensing technologies other than aerial imagery (primarily LIDAR) for collecting airport data. See also the Airports GIS website.

Explains the specifications for establishing geodetic control on or near an airport. It also describes how to submit the information to the National Geodetic Survey (NGS) for approval and inclusion in the National Spatial Reference System (NSRS) in support of aeronautical information surveys. See also Airports GIS Video Training Series.

Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.

See also Interim Guidance on Land Uses Within a Runway Protection Zone.

Provides guidance for conducting predesign, prebid, and preconstruction conferences for projects funded under the FAA airport grant program. This version adds quality acceptance as a topic of discussion for the preconstruction conference, items to be addressed in the engineer’s report, details about what should be included in the phasing plan, and discussion of construction management plans.

Contains specifications and guidance for the storage, handling, and dispensing of aviation fuel on airports. Additionally, this AC provides standards and guidance for the training of personnel who conduct these activities.

Please see the associated Addendum for a list of companies offering courses of instruction in line service training as well as supervisory training that are acceptable to the Administrator. We will update the Addendum on a quarterly basis.

Provides guidance on the development, installation, testing, approval, and maintenance of Automatic Dependent Surveillance – Broadcast (ADS-B) Out squitter units for airport ground vehicles. Using this AC, airports will be able to acquire approved and authorized airport ground vehicle ADS-B squitter units that are compliant with Title 14 Code of Federal Regulations (CFR), Part 91, Automatic Dependent Surveillance-Broadcast (ADS–B) Out Performance Requirements to Support Air Traffic Control (ATC) Service, as well as the initial set of ADS-B applications. Please note that the technical specifications for manufacturing ADS-B squitter units for airport ground vehicles are published in the FAA’s document, Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Specification, Version 2.4, published May 1, 2012.

Contact the appropriate FAA Airport District Office or Regional Airports Division to discuss Airport Improvement Program (AIP) eligibility.

Learn more about Automatic Dependent Surveillance-Broadcast (ADS-B).

Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.

See also:

• Airport Improvement Program (AIP) Guidance Letter 12-04: Avian Radars (3/5/2012) Discusses the eligibility of Avian Radar Systems and the justification required to use AIP grant funds to acquire and install them.
• Notice to Manufacturers of Airport Avian Radar Systems about AIP Buy American Requirement (10/28/2011). The FAA is requesting information to determine if waivers to this requirement are needed.

Provides information that airports can use to procure foreign object debris (FOD) detection equipment. Contains minimum performance specifications for systems and equipment that detect foreign objects on airports, including stationary radar, stationary electro-optical, stationary hybrid radar and electro-optical, and mobile radar.

See also Buy American Preferences to view:

• Notice of Decision to Issue Buy American Waivers for Foreign Object Debris (FOD) Detection Equipment (11/28/2010)
• Notice to Manufacturers of Foreign Object Debris (FOD) Detection Equipment (8/5/2010)
• Waiver request process

Contains specifications for the frangible connections used to support objects located in airfield safety areas, including fuse bolts, special material bolts, frangible couplings, tear-through fasteners, and tear-out sections.

This AC is based on the performance standards, specifications, and recommendations contained in the International Civil Aviation Organization (ICAO) Aerodrome Design Manual, Part 6, Frangibility, and the U.S. Air Force (USAF) Engineering Technical Letter (ETL) 01-20: Guidelines for Airfield Frangibility Zones.

Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).

Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers. The physical area covered in this AC is that which is bounded by the door of the passenger terminal area, on one end, to the door of the aircraft, on the other end. Although this AC refers only to aircraft boarding (enplaning), all references apply equally to disembarking (deplaning) with the described procedures occurring in reverse order.

The previous version of this AC discussed only the passenger lift scenario and associated equipment. This document updates that effort and addresses the other methods and equipment used to board an aircraft, including passenger boarding bridges, ramps, lifts, and aircraft boarding chairs.

Provides guidance on the design, construction, and operation of aircraft rescue and fire fighting (ARFF) training facilities.

This advisory circular (AC) contains the Federal Aviation Administration’s (FAA) standard for the non-Federal AWOS. This AC applies to anyone proposing to design, procure, construct, install, activate or maintain an AWOS.

Provides an interactive specification that airports can use in procuring Aircraft Rescue and Fire Fighting (ARFF) vehicles. It describes the selection process, vehicle requirements, and how to produce formal specifications.