Contains specifications for the frangible connections used to support objects located in airfield safety areas, including fuse bolts, special material bolts, frangible couplings, tear-through fasteners, and tear-out sections.
Foreign Object Debris Detection Equipment
Provides information that airports can use to procure foreign object debris (FOD) detection equipment. Contains minimum performance specifications for systems and equipment that detect foreign objects on airports, including stationary radar, stationary electro-optical, stationary hybrid radar and electro-optical, and mobile radar.
See also Buy American Preferences to view:
Airport Avian Radar Systems
Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.
Airport Ground Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Out Squitter Equipment
Provides guidance on the development, installation, testing, approval, and maintenance of Automatic Dependent Surveillance – Broadcast (ADS-B) Out squitter units for airport ground vehicles. Using this AC, airports will be able to acquire approved and authorized airport ground vehicle ADS-B squitter units that are compliant with Title 14 Code of Federal Regulations (CFR), Part 91, Automatic Dependent Surveillance-Broadcast (ADS–B) Out Performance Requirements to Support Air Traffic Control (ATC) Service, as well as the initial set of ADS-B applications. Please note that the technical specifications for manufacturing ADS-B squitter units for airport ground vehicles are published in the FAA’s document, Vehicle Automatic Dependent Surveillance - Broadcast (ADS-B) Specification, Version 2.4, published May 1, 2012.
Contact the appropriate FAA Airport District Office or Regional Airports Division to discuss Airport Improvement Program (AIP) eligibility.
Learn more about Automatic Dependent Surveillance-Broadcast (ADS-B).
Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.
Design of Aircraft Deicing Facilities
This AC provides standards and recommendations for use in the design of aircraft deicing facilities.
|150/5300-15A||AAS-100||Use Of Value Engineering For Engineering And Design Of Airport Grant Projects Provides guidance on using value engineering (VE) in airport projects funded under the Federal Aviation Administration's (FAA's) Airport Grant program.||09-30-2008|
General Guidance and Specifications for Aeronautical Surveys: Establishment of Geodetic Control and Submission to the National Geodetic Survey
Explains the specifications for establishing geodetic control on or near an airport. It also describes how to submit the information to the National Geodetic Survey (NGS) for approval and inclusion in the National Spatial Reference System (NSRS) in support of aeronautical information surveys. See also Airports GIS Video Training Series.
Standards for Using Remote Sensing Technologies in Airport Surveys
Provides guidance on the use of remote sensing technologies in the collection of data describing the physical infrastructure of an airport. This version is a substantial rewrite and includes new sections on remote sensing technologies other than aerial imagery (primarily LIDAR) for collecting airport data. See also the Airports GIS website.
Survey and Data Standards for Submission of Aeronautical Data Using Airports GIS
This AC provides the specifications and technical requirements for data collection conducted at airports in support of the FAA Airport Surveying – Geographic Information System (GIS) Program. The information furnished under these standards covers the entire spectrum of the FAA’s airport data requirements, including runway and stopway data, navigational aid data, obstruction data, and data on various airport features, including taxiways, aprons, and landmark features.
This version of the AC is a major rewrite; it now conforms to the new FAA enterprise data model and process of maintaining a single authoritative source of aeronautical data.
Airport Drainage Design
This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons. It incorporates the DOD Unified Facilities Criteria (UFC) draft document, Surface Drainage Design, dated August 1, 2006. This revision adds guidance that was not included in the original DOD document. See paragraph 5,, "Purpose of this Revision."
Airport Pavement Design and Evaluation
Provides guidance to the public on the design and evaluation of pavements at civil airports.
See also related Airport Design Software.
Measurement, Construction, and Maintenance of Skid Resistant Airport Pavement Surfaces
Contains guidelines and procedures for the design and construction of skid-resistant pavement; pavement evaluation, without or with friction equipment; and maintenance of high skid-resistant pavements.
|150/5320-15A||AAS-100||Management Of Airport Industrial Waste Provides basic information on the characteristics, management, and regulations of industrial wastes generated at airports. Provides guidance for the development of a Storm Water Pollution Prevention Plan (SWPPP) that applies best management practices to eliminate, prevent, or reduce pollutants in storm water runoff associated with particular airport industrial activities.||09-08-2008|
|150/5325-4B||AAS-100||Runway Length Requirements for Airport Design Provides design standards and guidelines for determining recommended runway lengths.||07-01-2005|
Standardized Method of Reporting Airport Pavement Strength - PCN
This AC provides guidance for using the standardized International Civil Aviation Organization (ICAO) method, called the Aircraft Classification Number – Pavement Classification Number (ACN-PCN) method, to report airport runway, taxiway, and apron pavement strength. Includes instructions for using the COMFAA program to calculate ACN values to determine PCN.
Also provides guidance for reporting changes to airport data that is generally published on Federal Aviation Administration (FAA) Form 5010, Airport Master Record, particularly those data elements associated with Gross Weight (Data Elements 35 through 38) and Pavement Classification Number (Data Element 39).
Access COMFAA and related Support Spreadsheet on our Airport Design Software page.
Standards for Airport Markings
This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons.
Segmented Circle Airport Marker System
This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.
Standards for Airport Sign Systems
Contains standards for the siting and installation of signs on airport runways and taxiways, including taxiway ending markers, location signs, runway distance remaining signs, mandatory hold signs associated with POFZ and CAT II/III operations, and many others.
Maintenance of Airport Visual Aid Facilities
This AC provides guidance and specifications for the Maintenance of airport Visual Aid Facilities.
Design and Installation Details for Airport Visual Aids
This AC provides guidance and recommendations about the installation of airport visual aids.
Specification for L-821, Panels for the Control of Airport Lighting
Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.
|150/5345-5B||AAS-100||Circuit Selector Switch Contains a specification for a circuit selector switch for use in airport lighting circuits.||09-14-2006|
Specification for L-824 Underground Electrical Cable for Airport Lighting Circuits
This AC provides specifications for L-824 underground electrical cable for airport lighting circuits.
Specification for Constant Current Regulators and Regulator Monitors
Contains a specification for constant current regulators (CCR) and a monitor for use with airport lighting circuits.