Passenger Facility Charge (PFC)
Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 184.108.40.206, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 220.127.116.11, Mounting System, to clarify Type II marker mounting and tethering requirements.
Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories
This AC contains the specifications for airport light bases, transformer housings, junction boxes, and accessories. This AC is not intended to be a compilation of currently available product designs. It provides the basic standard requirements for critical dimensions and performance requirements to which all manufacturers must demonstrate compliance.
Specification for Runway and Taxiway Signs
Contains the FAA specifications for unlighted and lighted signs to be used on taxiways and runways. See also Engineering Brief 67: Light Sources Other than Incandescent and Xenon for Airport and Obstruction Lighting Fixtures.
Low-Impact Resistant (LIR) Structures
Contains the FAA specifications for low-impact resistant (LIR) structures used to support approach lighting systems (ALS) at airports.
Specification for Runway and Taxiway Light Fixtures
Contains FAA specifications for in-pavement and elevated light fixtures used on airport runways and taxiways, including Runway Status Lights (RWSL), Takeoff Hold Lights (THL), Runway Intersection Lights (RIL), and Runway Entrance Lights (REL). See also--
Specification for Series to Series Isolation Transformers for Airport Lighting Systems
Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.
Specification L-854, Radio Control Equipment
Contains the specifications for radio control equipment to be used for controlling airport lighting facilities.
Specification for Portable Runway and Taxiway Lights
Contains the FAA standards for portable runway and taxiway lights and runway end identifier lights for temporary use to permit continued aircraft operations while all or part of a runway lighting system is inoperative.
Specification for Discharge-Type Flashing Light Equipment
Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).
See also Notice to Manufacturers of Airport Lighting and Navigation Aid Equipment about AIP Buy American Requirement (12/19/2011). The FAA is requesting information to determine if waivers to this requirement are needed.
Generic Visual Glideslope Indicators (GVGI)
Contains the FAA standards for generic visual glideslope indicators systems. GVGI systems provide pilots with visual glideslope guidance during approaches for landing at general aviation airports.
Airport Lighting Equipment Certification Program
This AC describes the Airport Lighting Equipment Certification Program (ALECP). It provides information on how an organization can get Federal Aviation Administration (FAA) acceptance as a third-party certification body (third-party certifier) and how manufacturers may get equipment qualified under the program. It includes a list of the equipments that are certified under the program. This AC does not impose requirements or mandate participation in the ALECP by any party. This revision clarifies the criteria that FAA will use to determine whether a certification body qualifies for participation and how equipment may be qualified.
Specification for L-884, Power and Control Unit for Land and Hold Short Lighting Systems
Contains the FAA standards for power and control units for land and hold short lighting systems.
Specification for L-893, Lighted Visual Aid to Indicate Temporary Runway Closure
Provides guidance in the design of a lighted visual aid to indicate temporary runway closure.
Airport Signing and Graphics
This AC provides guidance on airport terminal and landside wayfinding, signing, and graphics. It focuses on four areas of the airport: roadways, parking, curbside and ground transportation, and terminal. This version is a substantial rewrite and incorporates the recommendations and guidelines developed under Airport Cooperative Research Program (ACRP) Report 52, Wayfinding and Signing Guidelines for Airport Terminals and Landside, completed in 2011.
Operational Safety on Airports During Construction
Provides guidelines for operational safety on airports during construction. Principal changes include prohibiting construction in safety areas when associated runway or taxiway is open, providing guidance for incorporating safety risk management, and including checklists for writing Construction Safety and Phasing Plans (CSPP) and for daily inspections.
Use of Nondestructive Testing in the Evaluation of Airport Pavements
Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. It also briefly introduces other types of nondestructive measuring equipment to illustrate how supplementing NDT data with other test data may improve the quality and reliability of the pavement evaluation. This version updates Chapter 8, NDT-Based Evaluation and Design Updates, to reflect the requirements of the pavement design program FAARFIELD rather than the previous design program LEDFAA.
See also Airport Design Software.
Airside Applications for Artificial Turf
Provides guidance for the planning, design, installation, and maintenance of aviation grade artificial turf in areas adjacent to the operational areas of an airport.
Rapid Construction of Rigid (Portland Cement Concrete) Airfield Pavements
Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of rapid construction of rigid (Portland Cement Concrete) airfield pavements. This AC focuses on rigid airfield pavement construction. The material contained herein also applies to other types of airfield improvements where rapid construction is identified as the preferred construction method.
Airside Use of Heated Pavement Systems
Establishes minimum performance requirements for the design, construction, inspection, and maintenance of heated pavement systems for use in the Aircraft Operations Area (AOA).
Guidelines and Procedures for Maintenance of Airport Pavements
Provides guidelines and procedures for maintaining rigid and flexible airport pavements.
Because of the size of this document, it is available as one large file (see Complete) or as several smaller files (see Parts 1-3).
Guidelines and Procedures for Measuring Airfield Pavement Roughness
Provides guidelines and procedures for measuring and evaluating runway roughness as identified by surface profile data of rigid and flexible airport pavements. Provides technical procedures to quantify surface irregularities and to determine how surface irregularities may affect specific categories of airplanes.
Provides standards for the design of heliports serving helicopters with single rotors. Basic concepts can also be applied to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors; although many standards will not apply to these facilities.
This version adds guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO); turbulence effects; clearance between parking areas and taxi routes and within parking areas; minimum dimensions of curved approach/departure airspace; Touchdown/Positioning Circle (TDPC) Marking; Flight Path Alignment Guidance markings and lights; Emergency Helicopter Landing Facility Requirements (EHLF); FATO to FATO separation distance for simultaneous operations; revised standards for size of “H” for general aviation heliports; increased TLOF size when the FATO of a hospital heliport is not load bearing; and Heliport Protection Zone (HPZ) for hospital heliports. See "Principal Changes" for a complete list.
This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.