Passenger Facility Charge (PFC)
Standards for Airport Markings
This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons.
Specification for Wind Cone Assemblies
This AC contains a specification for wind cone assemblies to be used to provide wind information to pilots. This revision revises the equipment qualification requirements to be furnished under the Federal grant assistance program for airports, applies photometric requirements for internally lighted wind cones to both Size 1 and Size 2 windsocks, and makes editorial changes.
Airport Signing and Graphics
This AC provides guidance on airport terminal and landside wayfinding, signing, and graphics. It focuses on four areas of the airport: roadways, parking, curbside and ground transportation, and terminal. This version is a substantial rewrite and incorporates the recommendations and guidelines developed under Airport Cooperative Research Program (ACRP) Report 52, Wayfinding and Signing Guidelines for Airport Terminals and Landside, completed in 2011.
Segmented Circle Airport Marker System
This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.
Specification for L-824 Underground Electrical Cable for Airport Lighting Circuits
This AC provides specifications for L-824 underground electrical cable for airport lighting circuits.
Airport Drainage Design
This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons. It incorporates the DOD Unified Facilities Criteria (UFC) draft document, Surface Drainage Design, dated August 1, 2006. This revision adds guidance that was not included in the original DOD document. See paragraph 5,, "Purpose of this Revision."
Design of Aircraft Deicing Facilities
This AC provides standards and recommendations for use in the design of aircraft deicing facilities.
This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.
Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories
This AC contains the specifications for airport light bases, transformer housings, junction boxes, and accessories. This AC is not intended to be a compilation of currently available product designs. It provides the basic standard requirements for critical dimensions and performance requirements to which all manufacturers must demonstrate compliance.
Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.
Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns
Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).
Airport Lighting Equipment Certification Program
This AC describes the Airport Lighting Equipment Certification Program (ALECP). It provides information on how an organization can get Federal Aviation Administration (FAA) acceptance as a third-party certification body (third-party certifier) and how manufacturers may get equipment qualified under the program. It includes a list of the equipments that are certified under the program. This AC does not impose requirements or mandate participation in the ALECP by any party. This revision clarifies the criteria that FAA will use to determine whether a certification body qualifies for participation and how equipment may be qualified.
Design and Installation Details for Airport Visual Aids
Provides guidance and recommendations on the installation of airport visual aids.
Aircraft Boarding Equipment
Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers. The physical area covered in this AC is that which is bounded by the door of the passenger terminal area, on one end, to the door of the aircraft, on the other end. Although this AC refers only to aircraft boarding (enplaning), all references apply equally to disembarking (deplaning) with the described procedures occurring in reverse order.
The previous version of this AC discussed only the passenger lift scenario and associated equipment. This document updates that effort and addresses the other methods and equipment used to board an aircraft, including passenger boarding bridges, ramps, lifts, and aircraft boarding chairs.
Provides standards for the design of heliports serving helicopters with single rotors. Basic concepts can also be applied to facilities serving helicopters with tandem (front and rear) or dual (side by side) rotors; although many standards will not apply to these facilities.
This version adds guidance for pavement or structure larger than the touchdown and liftoff area (TLOF), but less than the size of the final approach and take off (FATO); turbulence effects; clearance between parking areas and taxi routes and within parking areas; minimum dimensions of curved approach/departure airspace; Touchdown/Positioning Circle (TDPC) Marking; Flight Path Alignment Guidance markings and lights; Emergency Helicopter Landing Facility Requirements (EHLF); FATO to FATO separation distance for simultaneous operations; revised standards for size of “H” for general aviation heliports; increased TLOF size when the FATO of a hospital heliport is not load bearing; and Heliport Protection Zone (HPZ) for hospital heliports. See "Principal Changes" for a complete list.
Standards for Using Remote Sensing Technologies in Airport Surveys
Provides guidance on the use of remote sensing technologies in the collection of data describing the physical infrastructure of an airport. This version is a substantial rewrite and includes new sections on remote sensing technologies other than aerial imagery (primarily LIDAR) for collecting airport data. See also the Airports GIS website.
Use of Nondestructive Testing in the Evaluation of Airport Pavements
Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement. It also briefly introduces other types of nondestructive measuring equipment to illustrate how supplementing NDT data with other test data may improve the quality and reliability of the pavement evaluation. This version updates Chapter 8, NDT-Based Evaluation and Design Updates, to reflect the requirements of the pavement design program FAARFIELD rather than the previous design program LEDFAA.
See also Airport Design Software.
Airside Applications for Artificial Turf
Provides guidance for the planning, design, installation, and maintenance of aviation grade artificial turf in areas adjacent to the operational areas of an airport.
Precision Approach Path Indicator (PAPI) Systems
Contains the FAA standards for the Precision Approach Path Indicator (PAPI) systems, which provides pilots with visual glideslope guidance during approach for landing.
Operational Safety on Airports During Construction
Provides guidelines for operational safety on airports during construction. Principal changes include prohibiting construction in safety areas when associated runway or taxiway is open, providing guidance for incorporating safety risk management, and including checklists for writing Construction Safety and Phasing Plans (CSPP) and for daily inspections.
Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 126.96.36.199, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 188.8.131.52, Mounting System, to clarify Type II marker mounting and tethering requirements.
Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
Standardized Method of Reporting Airport Pavement Strength - PCN
Provides guidance for using the standardized International Civil Aviation Organization (ICAO) method, called the Aircraft Classification Number – Pavement Classification Number (ACN-PCN) method, to report airport runway, taxiway, and apron pavement strength. Includes instructions for using the COMFAA program to calculate ACN values to determine PCN.
Also provides guidance for reporting changes to airport data that is generally published on Federal Aviation Administration (FAA) Form 5010, Airport Master Record, particularly those data elements associated with Gross Weight (Data Elements 35 through 38) and Pavement Classification Number (Data Element 39).
Access COMFAA and related Support Spreadsheet on our Airport Design Software page.
Specification for Series to Series Isolation Transformers for Airport Lighting Systems
Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.
Guide Specification for Aircraft Rescue and Fire Fighting (ARFF) Vehicles
Provides an interactive specification that airports can use in procuring Aircraft Rescue and Fire Fighting (ARFF) vehicles. It describes the selection process, vehicle requirements, and how to produce formal specifications.
Airside Use of Heated Pavement Systems
Establishes minimum performance requirements for the design, construction, inspection, and maintenance of heated pavement systems for use in the Aircraft Operations Area (AOA).