Airport Drainage Design
This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons. It incorporates the DOD Unified Facilities Criteria (UFC) draft document, Surface Drainage Design, dated August 1, 2006. This revision adds guidance that was not included in the original DOD document. See paragraph 5,, "Purpose of this Revision."
General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards
Provides the specifications for the collection of airport data for the FAA Airport Surveying – Geographic Information System (GIS) Program. Also explains how to submit data to the FAA, which will forward the safety critical data to the National Geodetic Survey (NGS) for independent verification and validation. The standards covered in this document provide critical information for the operation and safety of the National Airspace System (NAS) and are classified as critical by the International Civil Aviation Organization (ICAO). ICAO Annex 15 defines data as critical when “there is a high probability when using corrupted critical data that the continued safe flight and landing of an aircraft would be severely at risk with the potential for catastrophe.” The information furnished under these standards covers the entire spectrum of the FAA’s airport data requirements. See also FAA Airport Surveying - GIS Program and Airports GIS Video Training Series.
General Guidance and Specifications for Aeronautical Surveys: Establishment of Geodetic Control and Submission to the National Geodetic Survey
Explains the specifications for establishing geodetic control on or near an airport. It also describes how to submit the information to the National Geodetic Survey (NGS) for approval and inclusion in the National Spatial Reference System (NSRS) in support of aeronautical information surveys. See also Airports GIS Video Training Series.
Use Of Value Engineering For Engineering And Design Of Airport Grant Projects
Provides guidance on using value engineering (VE) in airport projects funded under the Federal Aviation Administration's (FAA's) Airport Grant program.
Contains the Federal Aviation Administration’s (FAA) standards and recommendations for the geometric layout and engineering design of runways, taxiways, aprons, and other facilities at civil airports.This substantial revision fully incorporates all previous changes to AC 150/5300-13 as well as new standards and technical requirements.
Predesign, Prebid, and Preconstruction Conferences for Airport Grant Projects
Provides guidance for conducting predesign, prebid, and preconstruction conferences for projects funded under the FAA airport grant program. This version adds quality acceptance as a topic of discussion for the preconstruction conference, items to be addressed in the engineer’s report, details about what should be included in the phasing plan, and discussion of construction management plans.
FAA Policy on Facility Relocations Occasioned by Airport Improvements or Changes
Reaffirms to the aviation community the FAA policy governing responsibility for funding relocation, replacement and modification of air traffic control and air navigation facilities that are made necessary by improvements or changes to the airport.
Airport Avian Radar Systems
Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.
Contains specifications for the frangible connections used to support objects located in airfield safety areas, including fuse bolts, special material bolts, frangible couplings, tear-through fasteners, and tear-out sections.
Engineered Materials Arresting Systems (EMAS) for Aircraft Overruns
Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).
Aircraft Boarding Equipment
Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers. The physical area covered in this AC is that which is bounded by the door of the passenger terminal area, on one end, to the door of the aircraft, on the other end. Although this AC refers only to aircraft boarding (enplaning), all references apply equally to disembarking (deplaning) with the described procedures occurring in reverse order.
The previous version of this AC discussed only the passenger lift scenario and associated equipment. This document updates that effort and addresses the other methods and equipment used to board an aircraft, including passenger boarding bridges, ramps, lifts, and aircraft boarding chairs.
Buildings for Storage and Maintenance of Airport Snow and Ice Control Equipment and Materials
Provides guidance for the site selection and design of buildings used to store and maintain airport snow and ice control equipment, store approved materials, and provide personnel areas required to support the requirements under the airport operator’s winter storm management plan.
Aircraft Rescue and Fire Fighting (ARFF) Training Facilities
Provides guidance on the design, construction, and operation of aircraft rescue and fire fighting (ARFF) training facilities.
Automated Weather Observing Systems(AWOS) for Non-Federal Applications
This advisory circular (AC) contains the Federal Aviation Administration’s (FAA) standard for the non-Federal AWOS. This AC applies to anyone proposing to design, procure, construct, install, activate or maintain an AWOS.
Guide Specification for Aircraft Rescue and Fire Fighting (ARFF) Vehicles
Provides an interactive specification that airports can use in procuring Aircraft Rescue and Fire Fighting (ARFF) vehicles. It describes the selection process, vehicle requirements, and how to produce formal specifications.
Performance Specification for Airport Vehicle Runway Incursion Warning Systems (RIWS)
This AC contains minimum performance specifications for systems and equipment airports use to provide a warning to drivers on an airfield about a potential runway incursion. This AC discusses two types of detection systems: a preconfigured, commercial off the shelf (COTS) system; and a system with custom hardware and software.
Airport Foreign Object Debris (FOD) Management
Provides guidance for developing and managing an airport foreign object debris (FOD) program. In addition, this AC provides specifications for the equipment used in FOD removal operations.
The described program addresses prevention, detection, removal, and evaluation as well as strategies and practices that can help reduce FOD at airports. The guidelines presented in this AC are advisory and can be implemented at the discretion of the airport operator in accordance with the airport operator’s approved Airport Certification Manual.
This AC cancels AC 150/5380-5B, Debris Hazards at Civil Airports, dated July 5, 1996.
Aircraft Fire and Rescue Facilities and Extinguishing Agents
Provides guidance on Aircraft Fire Extinguishing Agents and provides an acceptable methodology for complying with Title 14, Code of Federal Regulations, Part 139, Certification of Airports.
Airport Winter Safety and Operations
This advisory circular (AC) provides guidance to assist airport operators in developing a snow and ice control plan, conducting and reporting runway friction surveys, and establishing snow removal and control procedures. Version B of this AC cancelled AC 150/5220-13B, Runway Surface Condition Sensor Specification Guide, dated March 27, 1991. Consolidated file contains Change 1.
See also Notice to Manufacturers of Airport In-Pavement Stationary Runway Weather Information Systems about AIP Buy American Requirement (10/28/2011). The FAA is requesting information to determine if waivers to this requirement are needed.
Architectural, Engineering, and Planning Consultant Services for Airport Grant Projects
Provides guidance for airport sponsors in the selection and employment of architectural, engineering, and planning consultants under Federal Aviation Administration airport grant programs.
Development of State Standards for Nonprimary Airports
Provides guidelines for the development of State standards for and the use of State highway specifications for pavement construction at nonprimary public-use airports as provided for in title 49 United States Code (USC), Sections 47105(c) and 47114(d)(5), respectively.
Airport Master Plans
Provides guidance for the preparation of airport master plans that range in size and function from small general aviation to large commercial service facilities. Appendix D of this AC cancels Chapter 1, Section 5; Appendix 6; and Appendix 7 of AC 150/5300-13, Airport Design. Consolidated file contains Change 1.
Announcement of Availability of Airport-Related Research and Development Products
This AC explains how to obtain the latest airport-related research and development (R&D) products funded by the Federal Aviation Administration’s (FAA’s) Airports Organization, particularly the FAA’s Airport Technology Research and Development Branch, the Airport Cooperative Research Program (ACRP), the Innovative Pavement Research Foundation (IPRF), and the Airfield Asphalt Pavement Technology Program (AAPTP).
Announcement Of Availability: RTCA Inc., Document RTCA-221
Announces the availability of RTCA, Inc., Document RTCA/DO-221, Guidance and Recommended Requirements for Airport Surface Movement Sensors, dated April 24, 1994. Provides recommended minimum performance standards for airport surface movement sensors and specifies both sensor and system characteristics that provide guidance to airport systems designers, manufacturers, installers, and users of the equipment.
Cancels AC 150/5000-13, Announcement of Availability-RTCA Inc., Document RTCA-221, dated September 7, 1994.