Design, Construction, and Maintenance - General
Runway Length Requirements for Airport Design
Provides design standards and guidelines for determining recommended runway lengths.
Provides guidance to assist operators in planning, designing, and constructing seaplane base facilities.
Segmented Circle Airport Marker System
Sets forth standards for a system of airport marking consisting of certain pilot aids and traffic control devices.
Specification L-854, Radio Control Equipment
Contains the specifications for radio control equipment to be used for controlling airport lighting facilities.
Specification for Airport Light Bases, Transformer Housings, Junction Boxes, and Accessories
This AC contains the specifications for airport light bases, transformer housings, junction boxes, and accessories. This AC is not intended to be a compilation of currently available product designs. It provides the basic standard requirements for critical dimensions and performance requirements to which all manufacturers must demonstrate compliance.
Specification for Airport and Heliport Beacons
Contains equipment specifications for light beacons that are used to locate and identify civil airports, military airports, seaplane bases, and heliports.
Specification for Constant Current Regulators and Regulator Monitors
Contains a specification for constant current regulators (CCR) and a monitor for use with airport lighting circuits.
Specification for Discharge-Type Flashing Light Equipment
Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).
See also Notice to Manufacturers of Airport Lighting and Navigation Aid Equipment about AIP Buy American Requirement (12/19/2011). The FAA is requesting information to determine if waivers to this requirement are needed.
Specification for L-821, Panels for the Control of Airport Lighting
Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.
Specification for L-824 Underground Electrical Cable for Airport Lighting Circuits
Describes the specification requirements for L-824 electrical cables.
Specification for L-841 Auxiliary Relay Cabinet Assembly for Pilot Control of Airport Lighting Circuits
Contains the specification requirements for a relay cabinet used to control airfield lighting circuits. The L-841 consists of an enclosure containing a direct current (DC) power supply, control circuit protection and 20 pilot relays.
Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 18.104.22.168, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 22.214.171.124, Mounting System, to clarify Type II marker mounting and tethering requirements.
Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
Specification for L-884, Power and Control Unit for Land and Hold Short Lighting Systems
Contains the FAA standards for power and control units for land and hold short lighting systems.
Specification for L-890 Airport Lighting Control and Monitoring System (ALCMS)
Specifies the minimum requirements for an Airport Lighting Control and Monitoring System (ALCMS). The ALCMS simplifies the control and monitoring of lighted visual aids and enhances airport safety. The basic function of the system remains the same whether for a general aviation airport that supports only a few operations in a day or a large commercial airport which caters to hundreds of operations on any given day.
Specification for L-893, Lighted Visual Aid to Indicate Temporary Runway Closure
Provides guidance in the design of a lighted visual aid to indicate temporary runway closure.
Specification for Portable Runway and Taxiway Lights
Contains the FAA standards for portable runway and taxiway lights and runway end identifier lights for temporary use to permit continued aircraft operations while all or part of a runway lighting system is inoperative.
Specification for Runway and Taxiway Light Fixtures
Contains FAA specifications for in-pavement and elevated light fixtures used on airport runways and taxiways, including Runway Status Lights (RWSL), Takeoff Hold Lights (THL), Runway Intersection Lights (RIL), and Runway Entrance Lights (REL). See also--
Specification for Runway and Taxiway Signs
Contains the FAA specifications for unlighted and lighted signs to be used on taxiways and runways. See also Engineering Brief 67: Light Sources Other than Incandescent and Xenon for Airport and Obstruction Lighting Fixtures.
Specification for Series to Series Isolation Transformers for Airport Lighting Systems
Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.
Specification for Wind Cone Assemblies
Contains a specification for wind cone assemblies to be used to provide wind information to pilots of aircraft.
Standardized Method of Reporting Airport Pavement Strength - PCN
Provides guidance for using the standardized International Civil Aviation Organization (ICAO) method, called the Aircraft Classification Number – Pavement Classification Number (ACN-PCN) method, to report airport runway, taxiway, and apron pavement strength. Includes instructions for using the COMFAA program to calculate ACN values to determine PCN.
Also provides guidance for reporting changes to airport data that is generally published on Federal Aviation Administration (FAA) Form 5010, Airport Master Record, particularly those data elements associated with Gross Weight (Data Elements 35 through 38) and Pavement Classification Number (Data Element 39).
Access COMFAA and related Support Spreadsheet on our Airport Design Software page.
Standards for Airport Markings
Contains the FAA standards for markings used on airport runways, taxiways, and aprons. This AC cancels the Signs and Marking Supplement (SAMS).
This document is consolidated to include Change 1, dated November 17, 2010.
Standards for Airport Sign Systems
Contains standards for the siting and installation of signs on airport runways and taxiways, including taxiway ending markers, location signs, runway distance remaining signs, mandatory hold signs associated with POFZ and CAT II/III operations, and many others.
Standards for Specifying Construction of Airports
Provides standards for the construction of airports. Items covered in this AC include general provisions, earthwork, flexible base courses, rigid base courses, flexible surface courses, rigid pavement, fencing, drainage, turfing, and lighting installation.
Access related Pay Reduction Spreadsheets on our Airport Design Software page.
Use Of Value Engineering For Engineering And Design Of Airport Grant Projects
Provides guidance on using value engineering (VE) in airport projects funded under the Federal Aviation Administration's (FAA's) Airport Grant program.