Contains the FAA standards for portable runway and taxiway lights and runway end identifier lights for temporary use to permit continued aircraft operations while all or part of a runway lighting system is inoperative.

Contains the specification requirements for a relay cabinet used to control airfield lighting circuits.

Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.

Specifies the minimum requirements for an Airport Lighting Control and Monitoring System (ALCMS).

This AC describes the Airport Lighting Equipment Certification Program (ALECP). It provides information on how an organization can get Federal Aviation Administration (FAA) acceptance as a third-party certification body (third-party certifier) and how manufacturers may get equipment qualified under the program.

Contains the FAA specifications for low-impact resistant (LIR) structures used to support approach lighting systems (ALS) at airports.

Contains a specification for a circuit selector switch for use in airport lighting circuits.

Contains equipment specifications for light beacons that are used to locate and identify civil airports, military airports, seaplane bases, and heliports.

Contains a specification for constant current regulators (CCR) and a monitor for use with airport lighting circuits.

Provides guidance in the design of a lighted visual aid to indicate temporary runway closure.

Contains the FAA standards for generic visual glideslope indicators systems. GVGI systems provide pilots with visual glideslope guidance during approaches for landing at general aviation airports.

Contains the FAA standards for power and control units for land and hold short lighting systems.

Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.

Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).

This AC contains the specifications for radio control equipment to be used for controlling airport lighting facilities.

Effective six months after the issue date of this AC, only that equipment qualified in accordance with the specifications herein will be listed in accordance with AC 150/5345-53, Airport Lighting Equipment Certification Program.

Effective six months after the issue date of this AC, only equipment that is qualified with in this AC will be listed according to the requirements in AC 150/5345-53, Airport Lighting Equipment Certification Program.

This AC contains the FAA specification for obstruction lighting equipment.

Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of rapid construction of rigid (Portland Cement Concrete) airfield pavements.

Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.

This AC replaces AC 150/5200-35A, Submitting the Airport Master Record in Order to Activate a New Airport.

Provides guidelines and procedures for measuring and evaluating runway roughness as identified by surface profile data of rigid and flexible airport pavements.

Establishes minimum performance requirements for the design, construction, inspection, and maintenance of heated pavement systems for use in the Aircraft Operations Area (AOA).

This AC provides guidance on submitting accurate, complete on-airport proposals so the FAA can conduct an aeronautical study.

Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of off-peak construction of airport pavements using hot-mix asphalt (HMA) paving materials.

Provides guidance on using value engineering (VE) in airport projects funded under the Federal Aviation Administration's (FAA's) Airport Grant program.

Provides guidance for the planning, design, installation, and maintenance of aviation grade artificial turf in areas adjacent to the operational areas of an airport.

Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement.

Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).

This advisory circular contains standards and guidelines for the frangible connections used to support objects located in airfield safety areas and object free areas.

This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons. Consolidated to include Change 1, dated December 23, 2020.

This AC provides standards for the planning, design and construction of heliports serving helicopters with single, tandem (front and rear) or dual (side by side) rotors.

Provides guidance for the site selection and design of buildings used to store and maintain airport snow and ice control equipment, store approved materials, and provide personnel areas required to support the requirements under the airport operator’s winter storm management plan.

Provides recommended minimum performance standards for airport surface movement sensors and specifies both sensor and system characteristics that provide guidance to airport systems designers, manufacturers, installers, and users of the equipment.

Cancels AC 150/5000-13, Announcement of Availability-RTCA Inc., Document RTCA-221, dated September 7, 1994.

Provides basic information on the characteristics, management, and regulations of industrial wastes generated at airports.

This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.

This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons.

This AC provides guidelines and procedures for maintaining airport pavements.

This AC provides guidance for airport sponsors in the selection and engagement of architectural, engineering, and planning consultants.

In addition to the previous version, this AC cancels:

• AC 150/5300-9B, Predesign, Prebid, and Preconstruction Conferences for Airport Grant Projects
• AC 150/5370-6D, Construction Progress and Inspection Report-Airport Improvement Program (AIP)

This AC sets forth guidelines for operational safety on airports during construction.

This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.

The standard specifications contained in this advisory circular (AC) relate to materials and methods used for construction on airports.

For reporting of pavement strength, see AC 150/5335-5, Standardized Method of Reporting Airport Pavement Strength – PCR.

Contains guidelines and procedures for the design and construction of skid-resistant pavement; pavement evaluation, without or with friction equipment; and maintenance of high skid-resistant pavements.

Please see the letter cancelling AC 150/5300-18C and re-activating AC 150/5300-18B.

Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers.

This AC provides guidance on airport terminal and landside wayfinding, signing, and graphics.

This AC provides guidance and specifications for the Maintenance of airport Visual Aid Facilities.

This AC explains how to obtain the latest airport-related research and development (R&D) products funded by the Federal Aviation Administration’s (FAA’s) Airports Organization, particularly the FAA’s Airport Technology Research and Development Branch, the Airport Cooperative Research Program (ACRP), the Innovative Pavement Research Foundation (IPRF), and the Airfield Asphalt Pavement Technology Program (AAPTP).

This AC provides limited guidance on understanding and rating the surface condition of flexible (asphalt) and rigid (concrete) airfield pavements.

This AC discusses the Airport Pavement Management Program (PMP) concept, its essential components, and how it is used to make cost-effective decisions about pavement maintenance and rehabilitation (M&R).

This AC provides guidance and recommendations on the installation of airport visual aids. See the Principal Changes paragraph for a list of major changes to the document since the last version.

This AC provides a performance specification for an airport vehicle runway incursion warning system (RIWS).

This advisory circular provides guidance to assist airport operators in the procurement of snow and ice control equipment for airport use.

This AC explains the specifications for establishing geodetic control on or near an airport.

This AC provides guidelines for the development of State Aviation Standards for airport pavement construction at nonprimary public-use airports as well as the use of State Highway Material Specifications for airport pavement construction at nonprimary airports.

This AC provides standards and guidance for designing aircraft deicing facilities.