Eligibility and Evaluation of U.S. Military Surplus Flight Safety Aircraft Parts, Engines, and Propellers
This advisory circular (AC) provides information and guidance for use in evaluating and determining the eligibility of U.S. military surplus flight safety critical aircraft parts (FSCAP), engines, and propellers for installation on Federal Aviation Administration (FAA) type-certificated products. This AC is applicable to all U.S. military surplus FSCAP, engines, and propellers, irrespective of when and by what process these products or parts became available. In the absence of FSCAP classification of military surplus parts by the Department of Defense (DoD), such parts should be identified and classified as FSCAP using the guidance contained in this AC. For information and guidance on determining the eligibility of parts other than FSCAP, refer to AC 20-62, Eligibility, Quality, and Identification of Aeronautical Replacement Parts. Like all AC material, this AC is not mandatory and does not constitute a regulation. It is issued for guidance purposes and to outline one method of compliance with the rules. In lieu of following the method(s) prescribed herein without deviation, a person may elect to follow an alternative method, provided the FAA finds the alternative method to be an acceptable means of complying with the applicable requirements of Title 14 of the Code of Federal Regulations (14 CFR).
|20-143||ACE-100||Installation, Inspection, and Maintenance of Controls for General Aviation Reciprocating Aircraft Engines Provides guidance regarding the inspection, maintenance, and installation of engine controls with emphasis on the airframe portion of these systems. It provides a supplement to, but does not replace, the procedures in the manufacturers’ maintenance manuals. Where the content of the AC differs from, or conflicts with the manufacturers’ maintenance manual, instructions contained in the manufacturers’ manual take precedence over the guidelines provide in this AC.||06-06-2000|
|20-144||ANM-100||Recommended Method for FAA approval of Aircraft Fire Extinguishing System Components Provides guidance on the various aspects that should be considered in the FAA approval process of fire extinguishing system components manufactured under a Production Certificate (PC), components to be FAA approved under the Part Manufacturer Approval (PMA) process, or design changes to components originally approved by either method. This AC does not constitute a regulation, however, it provides a method, for obtaining approval of aircraft fire extinguishing system components. This is intended to enhance the standardization of all FAA Aircraft Certification Offices (ACO) and Manufacturing Inspection District Offices (MIDO) in the approval process of the critical components of an aircraft fire extinguishing system.||09-22-2000|
Methodology for Dynamic Seat Certification by Analysis for Use in Part 23, 25, 27, and 29 Airplanes and Rotorcraft
This advisory circular (AC) sets forth an acceptable means, but not the only means, for demonstrating compliance to the following by computer modeling analysis techniques validated by dynamic tests: • Title 14 Code of Federal Regulations (14 CFR) parts 23, 25, 27, and 29, §§ 23.562, 25.562, 27.562, and 29.562. • The Technical Standard Order (TSO) associated with the above regulations, TSO-C127/C127a.
|20-65A||AIR-200||U.S. AIRWORTHINESS CERTIFICATES AND AUTHORIZATIONS FOR OPERATION OF DOMESTIC AND FOREIGN AIRCRAFT Provides general information and guidance concerning issuance of airworthiness certificates for U.S. registered aircraft, and issuance of special flight authorizations for operation in the United States of foreign aircraft not having standard airworthiness certificates issued by the country of registry.||07-08-2004|
|20-148||AIR-100||Reusable Software Components Supplies one means for developers, integrators and applications to gain FAA acceptance of software.||12-07-2004|
|20-97B||AFS-306||Aircraft Tire Maintenance and Operational Practices This advisory circular (AC) provides recommended tire care and maintenance practices needed to assure the safety of support personnel and the continued airworthiness of aircraft. Specifically, this AC provides guidance on the installation, inflation, maintenance, and removal of aircraft tires. In addition, this AC provides guidance on those operational practices necessary to maintain safe aircraft operations. This AC is not mandatory and does not constitute a regulation. It is issued for guidance purposes and to outline acceptable tire maintenance and operational practices. In lieu of following this method without deviation, operators may elect to follow an alternative method that has also been found acceptable by the Federal Aviation Administration (FAA).||04-18-2005|
|20-152||AIR-100||RTCA, Inc., Document RTCA/DO-254, Design Assurance Guidance for Airborne Electronic Hardware This advisory circular (AC) applies to manufacturers and installers of products or appliances incorporating complex custom micro-coded components with hardware design assurance levels of A, B, and C. These complex custom micro-coded components include application specific integrated circuits (ASIC), programmable logic devices (PLD), field programmable gate arrays (FPGA), or similar electronic components used in the design of aircraft systems and equipment. This AC provides a means (but not the only means) to gain Federal Aviation Administration (FAA) approval by showing the equipment design is appropriate for its intended function. Further, using this AC will help you satisfy airworthiness requirements when these types of electronic components are implemented||07-05-2005|
|20-37E||AFS-350||Aircraft Propeller Maintenance Provides information and suggested procedures to increase service life and to minimize blade failures of metal propellers.||09-09-2005|
|20-154||AFS-300||Guide for Developing a Receiving Inspection System for Aircraft Parts and Material Provides guidance and information for incorporation into operators' existing receiving/inspection systems to help prevent the introduction of unairworthy parts into inventories.||12-12-2005|
|20-53B||AIR-100||Protection of Aircraft Fuel Systems Against Fuel Vapor Ignition Caused by Lightning Provides information and guidance concerning an acceptable means, but not the only means, of compliance with Parts 23 or 25 of the Federal Aviation Regulations (FAR) applicable to preventing ignition of fuel vapors due to lightning.||06-05-2006|
|20-156||AIR-100||Aviation Databus Assurance Provide a means to gain FAA approval of you aviation databus by showing the databus design performs it intended function and satisfies the applicable airworthiness requirements when install on an aircraft or aircraft engine||08-04-2006|
|20-73A||AIR-120||Aircraft Ice Protection Provides information relating to the substantiation of ice protection systems on aircraft.||08-16-2006|
|20-157||AIR-120||How to Prepare Reliability Assessment Plans for Aircraft Systems and Equipment This AC shows you how to develop and use a reliability assessment plan. An assessment plan documents the controlled, repeatable processes for assessing the reliability of aircraft and engine electronic and electrical systems, including their electromechanical elements and equipment||01-19-2007|
|20-77A||AFS-350||Use of Manufacturers' Maintenance Manuals Informs owners and operators about the usefulness of manufacturers’ maintenance manuals for servicing, repairing, and maintaining aircraft, engines and propellers.||04-06-2007|
|20-94A||AFS-350||Digital Clock Installation in Aircraft||04-13-2007|
|20-159||AIR-130||Obtaining Design and Production Approval of Airport Moving Map Display Applications Intended for Electronic Flight Bag Systems This AC will guide you in obtaining a design and production approval inder Technical Standard Order (TSO) C-165, Electronic Map Display Equipment for Graphical Depiction of Aircraft Position, for the software used to provide an airport moving map display(AMMD) intended for use on a Class 2 electronic flight bag (EFB).||04-30-2007|
|20-160||AIR-100||Onboard Recording of Controller Pilot Data Link Communication in Crash Survivable Memory The AC offers one way to achieve an acceptable level of performance for an aircraft recording system when a controller-pilot data communication capability is installed. We wrote this AC for aircraft equipment installers and type certificate applicants to identify design approval requirements for data link communication recording equipment.||02-21-2008|
|20-161||AIR-130||Aircraft Onboard Weight and Balance Systems This Advisory Circular (AC)gives manufacturers and installers an acceptable means of compliance to meet the installation, operation, and airworthiness requirements for aircraft onboard weight and balance systems (OBWBS)||04-11-2008|
|20-162||AIR-100||Airworthiness Approval and Operational Allowance of RFID Systems||09-22-2008|
|20-163||AIR-100||Displaying Geometric Altitude Relative to Mean Sea Level a. This advisory circular (AC) shows you how to gain a type certificate (TC), supplemental TC (STC), amended TC (ATC), amended supplemental TC (ASTC), or technical standard order (TSO) authorization for systems incorporating the presentation of geometric altitude relative to mean sea level (MSL) on electronic displays. b. This AC is not mandatory and does not constitute a regulation. In it, we describe an acceptable means, though it is not the only means, to gain approval. If you use the means described, you must follow it in all important respects.||07-09-2009|
Composite Aircraft Structure
This AC sets forth an acceptable means, but not the only means of showing compliance with the provisions of Title 14 of the Code of Federal Regulations (14 CFR) parts 23, 25, 27, and 29 regarding airworthiness type certification requirements for composite aircraft structures involving fiber reinforced materials, e.g., carbon and glass fiber reinforced plastics. Guidance information is also presented on the closely related design, manufacturing, and maintenance aspects. The information contained herein is for guidance purposes and is not mandatory or regulatory in nature.
Certification and Operation of Amateur-Built Aircraft
This Advisory Circular (AC) provides information about Title 14, Code of Federal Regulations (14 CFR) part 21, Certification Procedures for Products and Parts, § 21.191(g) for the purpose of operating amateur-built aircraft.
Designing and Demonstrating Aircraft Tolerance to Portable Electronic Devices
This advisory circular (AC) identifies RTCA, Inc., document DO-307, Aircraft Design and Certification for Portable Electronic Device (PED) Tolerance, dated October 11, 2007, and RTCA/DO-307, Change 1, dated December 16, 2008, as an acceptable means for designing and demonstrating aircraft tolerance to potential electromagnetic interference from portable electronic devices (PEDs).
This AC is not mandatory and does not constitute a regulation. In it, we describe an acceptable means, though not the only means, to demonstrate aircraft tolerance to PEDs
Airworthiness Approval of Enhanced Vision System, Synthetic Vision System, Combined Vision System, and Enhanced Flight Vision System Equipment
a. In this advisory circular (AC), the Federal Aviation Administration (FAA) provides guidance on airworthiness approval of enhanced vision system (EVS), synthetic vision system (SVS), combined vision system (CVS), and enhanced flight vision system (EFVS) equipment installation.
b. This AC provides specific system performance guidance on enhanced and synthetic vision systems and equipment. Other existing ACs address flight guidance symbology, head-up displays (HUD) and visual display characteristics (for example, AC 25-11A, Electronic Flight Deck Displays, and AC 25.1329-1B, Approval of Flight Guidance Systems). For a complete listing of related regulations and guidance, refer to appendix 9. This AC complements existing guidance.
c . In this AC, terrain awareness and warning system (TAWS) refers to a system used for fixed-wing aircraft and helicopter terrain awareness and warning system (HTAWS) refers to a system used for rotorcraft.
d. This AC is not mandatory and does not constitute a regulation. This AC describes an acceptable means, but not the only means, to install enhanced and synthetic vision technologies. However, if you use the means described in this AC, you must follow it in all aspects.