This AC contains the FAA standards for markings used on airport runways, taxiways, and aprons. Consolidated to include Change 1, dated December 23, 2020.

This AC provides standards for the planning, design and construction of heliports serving helicopters with single, tandem (front and rear) or dual (side by side) rotors.

This AC provides guidance to assist operators in planning, designing, and constructing seaplane bases and associated facilities.

Provides guidance for the preparation of airport master plans that range in size and function from small general aviation to large commercial service facilities.

Contains the FAA specifications for low-impact resistant (LIR) structures used to support approach lighting systems (ALS) at airports.

Contains the FAA standards for portable runway and taxiway lights and runway end identifier lights for temporary use to permit continued aircraft operations while all or part of a runway lighting system is inoperative.

Contains the specification requirements for a relay cabinet used to control airfield lighting circuits.

Provides guidance for the planning, coordination, management, design, testing, inspection, and execution of rapid construction of rigid (Portland Cement Concrete) airfield pavements.

Contains a specification for a circuit selector switch for use in airport lighting circuits.

Provides guidance for the site selection and design of buildings used to store and maintain airport snow and ice control equipment, store approved materials, and provide personnel areas required to support the requirements under the airport operator’s winter storm management plan.

Announces the availability of RTCA, Inc., Document RTCA/DO-221, Guidance and Recommended Requirements for Airport Surface Movement Sensors, dated April 24, 1994.

Contains equipment specifications for light beacons that are used to locate and identify civil airports, military airports, seaplane bases, and heliports.

Provides guidance on the use of avian radar systems to supplement an airport’s Wildlife Hazard Management Plan (WHMP) and reduce the potential avian threats to aircraft.

Contains the Federal Aviation Administration (FAA) specifications for series to series isolation transformers for use in airport lighting systems.

Provides guidance for the planning, design, installation, and maintenance of aviation grade artificial turf in areas adjacent to the operational areas of an airport.

Focuses on nondestructive testing (NDT) equipment that measures pavement surface deflections after applying a static or dynamic load to the pavement.

Provides basic information on the characteristics, management, and regulations of industrial wastes generated at airports.

This AC provides standards for a system of airport marking consisting of certain pilot aids and traffic control devices.

This AC provides guidance for engineers, airport managers, and the public about the design and construction of airport surface storm drainage systems; and subsurface drainage systems for paved runways, taxiways, and aprons.

This AC provides guidelines and procedures for maintaining airport pavements.

This AC describes the Airport Lighting Equipment Certification Program (ALECP). It provides information on how an organization can get Federal Aviation Administration (FAA) acceptance as a third-party certification body (third-party certifier) and how manufacturers may get equipment qualified under the program.

This AC provides specifications for L-824 underground electrical cable for airport lighting circuits.

Contains standards for the planning, design, installation, and maintenance of Engineered Materials Arresting Systems (EMAS) in runway safety areas (RSAs).

Contains a specification for constant current regulators (CCR) and a monitor for use with airport lighting circuits.

This AC assist airports in complying with the laws and regulations regarding individuals with disabilities by: (1) identifying the relevant statutes and regulations affecting airports; (2) presenting the main features of each of the statutes and regulations; and (3) listing sources of assistance or additional information.

This AC provides information on the process of planning airport passenger terminal facilities. It combines and supersedes two previous FAA ACs on this topic: AC 150-5360-13, Planning and Design Guidelines for Airport Terminal Facilities, and AC 150/5360-9, Planning and Design Guidelines for Airport Terminal Facilities at Non-hub Locations.

This advisory circular contains standards and guidelines for the frangible connections used to support objects located in airfield safety areas and object free areas.

This AC sets forth guidelines for operational safety on airports during construction.

The standard specifications contained in this advisory circular (AC) relate to materials and methods used for construction on airports.

This AC contains standards and guidance for airport operators on the issuance of Notice to Air Missions (NOTAM).

This advisory circular contains the Federal Aviation Administration (FAA) specifications for light fixtures to be used on airport runways and taxiways.

Contains guidelines and procedures for the design and construction of skid-resistant pavement; pavement evaluation, without or with friction equipment; and maintenance of high skid-resistant pavements.

Provides guidance in the design of a lighted visual aid to indicate temporary runway closure.

Contains the FAA standards for generic visual glideslope indicators systems. GVGI systems provide pilots with visual glideslope guidance during approaches for landing at general aviation airports.

Provides design standards and guidelines for determining recommended runway lengths.

Provides guidance in the design of systems for interactive training of airport personnel, which are eligible for funding under the Airport Improvement Program (AIP) and with Passenger Facility Charge (PFC) revenues.

Contains information, references and guidelines for construction of Aircraft Rescue and Fire Fighting (ARFF) station building design.

Provides the specifications for the collection of airport data for the FAA Airport Surveying – Geographic Information System (GIS) Program.

Provides guidance, specifications, and standards for painting, marking, and lighting of ground vehicles operating in the airport air operations area (AOA).

Contains the specifications for discharge-type flashing light equipment to be used for runway end identification lights (REIL) and for an omni-directional approach lighting system (ODALS).

Provides guidance on the design, construction, and operation of aircraft rescue and fire fighting (ARFF) training facilities.

Establishes minimum performance requirements for the design, construction, inspection, and maintenance of heated pavement systems for use in the Aircraft Operations Area (AOA).

Contains the FAA standards for power and control units for land and hold short lighting systems.

Provides guidelines and procedures for measuring and evaluating runway roughness as identified by surface profile data of rigid and flexible airport pavements.

Provides the specified manufacturing requirements for panels used for remote control of airport lighting and auxiliary systems.

Provides guidance to assist airport operators in preparing for water rescue operations.

Provides an interactive specification that airports can use in procuring Aircraft Rescue and Fire Fighting (ARFF) vehicles.

Provides guidance on the use of remote sensing technologies in the collection of data describing the physical infrastructure of an airport.

Contains the FAA's performance standards, specifications, and recommendations for the design, manufacture, testing and maintenance of equipment used in the boarding of airline passengers.

This AC provides guidance on airport terminal and landside wayfinding, signing, and graphics.

This AC provides guidance and specifications for the Maintenance of airport Visual Aid Facilities.

This advisory circular provides guidance to assist airport operators in the procurement of snow and ice control equipment for airport use.

This AC contains the specifications for radio control equipment to be used for controlling airport lighting facilities.

This AC provides guidance and recommendations on the installation of airport visual aids. See the Principal Changes paragraph for a list of major changes to the document since the last version.

This AC contains the FAA specification for obstruction lighting equipment.

This AC provides guidance to assist airport operators in preparing for Aircraft Rescue and Fire Fighting (ARFF) communications.

This AC contains the FAA standards for the Precision Approach Path Indicator (PAPI) systems, which provides pilots with visual glideslope guidance during approach for landing.

This Advisory Circular (AC) contains the Federal Aviation Administration (FAA) standards for the siting, design, and installation of signs on airport runways and taxiways.

This advisory circular contains the specifications for airport light bases, transformer housings, junction boxes, accessories, and elevated light fixture covers and stakes.

This AC contains the FAA's standards for retroreflective markers for airport runways and taxiways.

This AC contains references to the minimum standards for the selection and performance of aircraft rescue and firefighting personal protective equipment (PPE), self-contained breathing apparatus (SCBA), and powered rescue tools.

This advisory circular contains the Federal Aviation Administration (FAA) specifications for unlighted and lighted signs to be used on taxiways and runways.

This AC explains the specifications for establishing geodetic control on or near an airport.

This AC provides standards and guidance for designing aircraft deicing facilities.

This AC provides guidance on submitting accurate, complete on-airport proposals so the FAA can conduct an aeronautical study.

This AC provides guidance to assist airport operators in developing a snow and ice control plan, assessing and reporting airport conditions through the utilization of the Runway Condition Assessment Matrix (RCAM), and establishing snow removal and control procedures.